exclusive's '11 Camry Thread

[exclusive]

12/7/11 - New Wheels!



Current mod list:

• 19x8.5 MRR HR2
• Tein S-Tech Camry Springs
• 6000k HID Low and Fogs
• Interior/Exterior LEDs
• Tint: F 20%/ R 5%
• Yakima Rack (off for the winter)

UPDATE



RIP 1/22/11 ... See Pg. 9

I got it on 9/6/10 and it's already been almost a month.

Car: 2011 Camry LE 2.5L with factory alloys

Current Mods:
5% rear tint, 15% driver & passenger
DDM 6000k HID Kit
LEDs: interior/exterior
Custom LED lights in the fog light area
Tein S. Tech for Camry (1.6F/1.5R)
MRR HR2: 19x8.5" +45

UPDATE






First wash with tints:



LEDs:


LED fog mod:

[bleachigo]

You are such a tease.Enough foreplay,show it already(no homo).

[exclusive]

Hahaha. The lug nuts will be in this week and I'll put the wheels on. I hope it doesn't look like a 4x4 without springs

[BlackCamSe]

whered you get the LED's for the side marker lights on the headlight?

[exclusive]

did you need to quote my whole post lol
got em here:
http://cgi.ebay.com/ws/eBayISAPI.dll...m=170515839231

[BlackCamSe]

Originally Posted by exclusive

did you need to quote my whole post lol
got em here:
http://cgi.ebay.com/ws/eBayISAPI.dll...m=170515839231

Thanks! Just ordered 2. Just a question. Looking under the hood it's reallll tight to get to that bulb. Did you have to take the headlight off to get to it.

[Pawel062]

car is looking good. it will look a little bit like suv but ain't bad. get some springs or coils later n will be good.

[exclusive]

Originally Posted by BlackCamSe

Thanks! Just ordered 2. Just a question. Looking under the hood it's reallll tight to get to that bulb. Did you have to take the headlight off to get to it.

No, just take off the 2 or 3 clips for the splash guard for the wheel. Pull it back and reach in to get to the bulb. If you're doing the driver side, turn your wheels to the right. Passenger side, turn your wheels to the left.

Originally Posted by Pawel062

car is looking good. it will look a little bit like suv but ain't bad. get some springs or coils later n will be good.

I can't wait for the lug nuts to come in!

[BlackCamSe]

had one more question...i just ordered the same HID kit as you....how is the glare? Did you cover the squirrel spotters?

[zee3b]

Did you get the 35w kit or the 55w?

[BlackCamSe]

Originally Posted by zee3b

Did you get the 35w kit or the 55w?

35....didnt want to melt the housing..aha

[exclusive]

Originally Posted by BlackCamSe

had one more question...i just ordered the same HID kit as you....how is the glare? Did you cover the squirrel spotters?

I have the 35W kit. I didn't mess with the squirrel spotters (who came up with this? lol) The boxes can be seen when you are facing a wall, but I've aimed my lights a little bit down to not blind people. So basically, when I'm behind a car, the cutoff of my lights is below the top of their trunk.
Also, my sig is way different then what an actual eye sees. That was my blackberry camera and it just intensifies the light. You'd think the glare is crazy by that pic but it isn't.

[BlackCamSe]

Originally Posted by exclusive

I have the 35W kit. I didn't mess with the squirrel spotters (who came up with this? lol) The boxes can be seen when you are facing a wall, but I've aimed my lights a little bit down to not blind people. So basically, when I'm behind a car, the cutoff of my lights is below the top of their trunk.
Also, my sig is way different then what an actual eye sees. That was my blackberry camera and it just intensifies the light. You'd think the glare is crazy by that pic but it isn't.

would it be possible for you to take a picture of the beam pattern against a wall from the inside of the car? So i have an idea of how low to aim them

[exclusive]

Originally Posted by BlackCamSe

would it be possible for you to take a picture of the beam pattern against a wall from the inside of the car? So i have an idea of how low to aim them

Yea np. I'll try to do it tonight.

[BlackCamSe]

thanks bro