DIY - Corolla 98 - 02 Rack & Pinion Replacement - Toyota Nation Forum : Toyota Car and Truck Forums
8th Generation (1998-2002) Specific discussion of the 8th generation

 
LinkBack Thread Tools Display Modes
#1 Old 09-25-2012, 12:28 PM
CorollaCarClub.proboards.
 
RinconRolla98's Avatar
 
Join Date: Mar 2007
Location: Florida
Posts: 925
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Thanks: 1
Thanked 54 Times in 35 Posts
iTrader Score: 0 reviews
(Thread Starter)
Exclamation DIY - Corolla 98 - 02 Rack & Pinion Replacement

This is a DIY for a Rack & Pinion for a Corolla 98 - 02 as well as other suspension parts .





In this DIY I have my front bumper off for another job I was doing but you dont have to take it off . But in the end it was more movability under the car with it off . But make sure you jack your car up as high as you can so you have plenty of room underneath it . Straighten out the steering wheel and lock it into place removing the key . Very important to keep it locked .





First thing I did was remove the outer tie rod and the sway bar link .











The second thing I did was remove the cover that covers the knuckle on the steering colum , With the steering wheel locked you can remove the lower bolt . Then I went to the rack & pinion lines and removed them . Then I went behind the exhaust manifold and removed the heat plate that covers some hoses and brackets that later you need to remove













Then I placed a jack to support the lower engine , which I really didn't need only to raise the engine a little to remove the lower engine mount , Now the easiest way and the only way to remove the rack & pinion is you have to remove the sub frame completly , because the lower engine mount blocks the one lower bolt on the rack . Start by removing the ball joint bolts first then work your way to the sway bar and complete sub frame . Always remember where the bolts come out of .









Once the sub frame is removed then you remove the lower motor mount and the lower rack & pinion shield then the bracket that hold the lines to the rack frame .









Before pulling out the rack from the drivers side you need to remove the passenger outer tie rod then pull and tilt the passenger side up past the exhaust so that the rack box slides out the hole . This is the same way you put back in the rack . Before removing the left outer tie rod make sure you mark or count the threads so when you put them on the new one you are close . DO NOT REMOVE the nuts on the rack & pinion cause it is pressrized and you dont want to remove it until the rack is completly on this is the last thing you put back on is the hoses . If you release the pressure then you will not be aligned . The rack is on a blind alignment from the manufacture .







Make sure when you put this lower motor mount back on you put the rubber heat shield facing towards the exhaust or else your motor mount will melt .







Now in this situation this car has 350,000 miles on it so I replaced the lower motor mount , sway bar links , rack & pinion bushing , sway bar bushing . I removed all the oil and grease from the sub frame and shield . In my situation I used anti sieze on certian bolts and lock tight medium on the sub frame cause I noticed they had some when I removed them .



Make sure you put your outer tie rods on like they were when you took them off .



This knuckle slides on make sure it goes on flush then tighten .









Then is reverse you put everything back on , make sure you shields are on , then last step connect the lines to the rack , bleed the power steering box and add new fluid start your car turn your wheel till the air comes out then off to the aligment shop .

Need More help go to : www.CorollaCarClub.proboards.com or http://rinconrolla98.blogspot.com

.
RinconRolla98 is offline  
Sponsored Links
Advertisement
 
#2 Old 09-26-2012, 12:04 AM
New TN User
 
Join Date: May 2008
Location: LA
Posts: 40
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Thanks: 0
Thanked 2 Times in 2 Posts
iTrader Score: 0 reviews
f-ing amazing! that looks difficult though..
dorkiedoode is offline  
#3 Old 10-07-2012, 10:29 PM
Official TN Member
 
Join Date: Nov 2011
Location: New York City
Posts: 52
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Thanks: 5
Thanked 1 Time in 1 Post
iTrader Score: 0 reviews
I had the rack replaced on my 98 corolla last year and now I feel hot air coming from underneath the steering column. It's a real pain in the @$$ especially when I have the a/c on in the summer and I feel 100ş heat coming from under the dash while im driving. What's that about?
irbryanxp is offline  
Sponsored Links
Advertisement
 
Reply

  Toyota Nation Forum : Toyota Car and Truck Forums > Toyota Passenger and Sports Car Forums > Corolla and Matrix Forum > 8th Generation (1998-2002)

Bookmarks

User Tag List

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome