Toyota Nation Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-12 of 12 Results
  1. Camry 1st and 2nd Gen (1983-86) and (1987-91)
    I have a 1990 Camry, 4 cylinder 2.0L engine, that I've been trying to get running. I couldn't hear the fuel pump pressurizing so I started to attempt to replace it. From what I looked up I could get to the fuel pump by pulling the back seat out and opening the housing there. When I pulled it...
  2. Camry 1st and 2nd Gen (1983-86) and (1987-91)
    using these coils for a different car a 1990 Camry stock springs are already a half inch lower but I need a lot lower than that so what is it the lowest option for lowering springs any brand is fine I'm looking for around it on the package label 2 in to 3 inch drop please let me know thanks a lot
  3. Camry 1st and 2nd Gen (1983-86) and (1987-91)
    I bought a ‘90 Camry about a month ago, I’ve had no issue until this morning while driving home from work. There’s usually a bit of shake when driving it but a loud thunking started in my drivers side wheel well. It sounds like something is hitting my wheel and gets worse when turning left. I’m...
  4. Camry 1st and 2nd Gen (1983-86) and (1987-91)
    Working on a blown head gasket (lord please let it just be the gasket), I don't have an engine hoist so I'm trying to pull the head off with the intake manifold and fuel rail connected and leaving the engine in the vehicle. This is the first time I've ever done any engine work ever. So far it's...
  5. Camry 1st and 2nd Gen (1983-86) and (1987-91)
    Hey guys! Yesterday I was driving to work (car is a 1990 Toyota Camry) when I had to accelerate really quickly. I floored it (which is something I almost never do), and afterwards the car has been having issues shifting. At first, it seemed like I couldn't shift past 2nd gear, automatic...
  6. Camry 1st and 2nd Gen (1983-86) and (1987-91)
    Hello, I do not have any pictures at the moment but I have had the pleasure of driving my mom's Camry for a few years and it is probably my favorite vehicle that I have driven. Looking at detailing and some repairs to get it feeling closer to factory to give back to her after school, or when I...
  7. Camry 1st and 2nd Gen (1983-86) and (1987-91)
    I need step by step directions on how to put my drivers side front wheel bearing hub assembly back together. I paid someone to take it apart and put it back together, but now that it's apart, the guy is gone and I need to put it back together myself. I got the old wheel bearing pressed out and...
  8. Camry 1st and 2nd Gen (1983-86) and (1987-91)
    Hello. I have a 1990 Camry with 27,978 miles, I lifted the trunk lid and BAM. It appears that the piece that swiveles at the end of the torsion bar is sheared off!?? I'm having a hard time trying to remove the whole assembly. Im afraid the bar is going to POP out and snap my wrist. (will it ?)...
  9. Camry 1st and 2nd Gen (1983-86) and (1987-91)
    Hi, I have a 1990 Camry. During my latest project installing a remote starter, I decided to cut a wiring harness from the center console that I thought wasn't used. It turned out to be the transmission ECT selector switch. The problem is that the ECT pattern selector switch harness under the...
  10. Camry 1st and 2nd Gen (1983-86) and (1987-91)
    Hi, I ordered new control arms for my 1990 Camry because the bushings on the original were completely shot. I also got all new hardware so things would stay rust free for another 22 years! I installed everything, but I'm not sure I did the sway bar retainers right. These are PNC 48817A on the...
  11. Camry 1st and 2nd Gen (1983-86) and (1987-91)
    Hi all, I am new to this forum and have searched for information regarding this. My blower motor used to be really loud when it was turned on like I could hear it outside the car. It has since stopped working at all. The AC light will still come on and it clicks when I turn on the fan switch. I...
  12. Camry 1st and 2nd Gen (1983-86) and (1987-91)
    My teenage son left the door ajar and the battery went dead. He jumped the car and he got nothing. The 80amp alt. fuse-able link blew so I replaced that and now the car just turns over but will not fire up. I have the feeling he may have reversed the jumper cables. Is there another fuse that...
1-12 of 12 Results
Top