Search Results for ‘adjustment’

Hi all, new to the forum browsed for years but I have a 2019 Camry 4cyl and recently did air suspension on it I have adjustable rear control arms but cant seem to find anything for the front. I know camber bolts are an option but I had them and they dont have enough adjustment. Any suggestions ?

My parents have a Corolla S and the trunk will not close. They are short on cash and I am hoping I can help them fix it while I am here for Thanksgiving. The trunk has always been difficult to close and the plastic on the latch mechanism looks a little mangled. The mechanism does appear to...

Hello people , am looking for answers and that's how i found this site. Good site.:facepalm:

95 Toyota Corolla DX 1.8L So, after completing a bunch of front suspension work myself (replaced steering rack, driver side control arm (new front bushing came installed with it), sway bar links and bushings, rear struts, and new "used" tires), I then took the Corolla in for an alignment...

This is a continuation of this thread: http://www.toyotanation.com/forum/130-7th-generation-1993-1997/647361-need-little-help-one-4.html I just don't want to hijack it, as it's about a different purpose other than the TPS. To test the TPS resistance between pins, I used this harness I cut off...

I have read several threads on this forum about adjusting the rear drum brakes - usually in conjunction with a brake job - and most mention the rear brakes are adjusted by operating the parking brake, *not* by backing up and stopping like most old-school drum brake systems. My question is: if...

Okay so I cant seem to figure out how to adjust the headlights on my 92 camry. I just did a headlight restoration on the headlights and put in brighter bulbs so I can see at night better. Anyways I keep reading about these vertical and horizontal adjustment screws. Where are they located? I...

Hey all! Haven't posted in a while by I have a new set of HID's to install this weekend and have a problem I need to get remedied before hand. Last year some fool apparently backed into my driver's side housing leaving me with some unwanted paint, a cracked housing, and what appears to be a...

When I adjusted my valve lash I didn't find tdc, I don't turn the motor "x" degrees. I remove the valve cover and adjusted the valves that are on the back side of the cam lobe. I bump the engine with the starter slightly and adjust other valves. Repeat until I got them all. Hope this makes...

I just bought a 2006 Avalon. I know how to adjust the low beam but the high beam is lower than the low beam and I know the low beam isn't to high it could even come up some more but I really need to get the high beam up more. anybody got any ideas? Thanks L. Hall

Today I noticed on the warranty for my engine, it says So I went out to check the valves to see how off they were, and was pleasantly surprised. All my valves were within 2 thousandths of an inch of the lowest clearance, so I figure it'll be ok. TOOLS NEEDED: -30 mm socket -19 mm socket...

Hi, I need to get my emissions testing done and they said they can't test it if the idle is over 1200 rpm. He said it's at about 1400 rpm now. I'm looking for the idle adjustment screw/valve so I can do this myself. I seem to have misplaced my Chilton manual and I haven't been able to find any...

hey guys/girls i recently blew the head gasket in my car 92 celica gt (5sfe) and finished everything up last night and when i went to start it cranked up perfect and idled great but is ticking in the head. I was wondering if anyone had any advice on adjusting the valves on it i would really like...

I took a look at the engine compartment yesterday and sad to say, OMG!, there is like no room to put the ballast in! I see a spot next to the headlamp where it seems that the OEM HID ballast would go but I don't really trust putting a velcro on it as I still want to zip tie it to secure it into...