Search Results for ‘bolt’

I'm having a difficult adventure attempting to learn the size of both the bottom and top bolts for my 05 toyota matrix 1ZZ, xr lol Thread type, length & thread diameter Top bolt part #90119 08530 Bottom #90119 08908 Dealership is overloaded with orders for em so I figure I'll head to another...

Hi All, I drive a Toyota Corolla 2003 LE edition with almost 200k miles and its still going strong! :D My check engine light went on I got an upstream o2 sensor code and my gas mileage has been crappy. So my plan is to replace the o2 upstream sensor myself. From what I understand I need to...

I've been searching the internet for over an hour and I can't find any posts or products that would seem to match what I'm looking for. I live in a state that requires a front license plate and I don't want to drill holes in my bumper, so I thought I'd get a recover-hook (aka tow hook) bolt...

Title. The TRD brace is set to come in Friday, but I still need to buy a torque wrench and sockets.

Can I still drive my car if I only have the top bolt for my alternator in

I have a 2005 Highlander v6 awd, the bolt is listabout 4 inches and about .3 inches in diameter, double threads one set on each end, with a hex head on one end. I was doing an oil change and when I took the skid plate off, this bolt fell out! Any body know what it could be from?

Hi all, Found this bolt under the engine bay on the floor today. It's a steel bolt with inner hex head/Allen head, 7.5mm thread width, 30mm long, and thread starts at 20mm. Where does it come from? It seems to be broken off a while ago, with rust at the breaking thread end. Just did the drive...

Hi, I replaced my ATF 3 months ago. When I unscrewed the plug, it was tight at first, then it became loose, then there was some more anormal resistance in the middle of the process. Same thing when I put the plug back in. I replaced the ATF again today. The plug was tight, but the same...

I just cleaned my seatbelts in my corolla. They were slow. I rewound the springs on both sides. Drivers side was easy. Passenger was a little more difficult. However they are faster but still not super fast.. I read up and found out that if they are dirty that can make it slow. I just got done...

Hey guys I was wondering if anyone knew what size bolts to use for the engine stand and where on the engine the mounting spots were. I was told I needed M12 x 1.25 bolts but I don't know what that means, I assume M12 is the metric head size and 1.25 is the thread size but not for sure haha...

:facepalm: I was quite proud of myself successfully removing the bolts and plastic closures to lower my front bumper. Then...removing my original headlight, I snapped the bolt that is closest to the center of the car with a 10mm socket wrench. :wtf: The specific placement of the bolt, would...

I've got a 1994 Corolla DX A/T with nuts missing from the alternator lock and pivot bolts. A 14mm wrench fits the hex head of the bolt, but I'm stumped as to what size nut I need and where to buy one inexpensively. Is it a 14mm 1.5 or 14mm 2.0 nut that I need, and where besides Toyota can I...

I have one rounded caliper bolt on the rear brakes, and I'm wondering if anyone's tried the Irwin Grip Bolt Remover or this Craftsman Bolt Out Damaged Bolt removal tool, and if so, was it a success? Were your bolts possibly seized? (I mean, why else would the heads be rounded, but want to know...

hello, I am new to this site and am in dire need of some help identifying this part, it stripped when i was removing the pressure hose and return hose, the bolt to tighten them on, if anyone knows of a place to order it that would ship to Canada or can provide me with repair solutions it would...

To make a long story short, i was reinstalling the crossmember and i ended up somehow messing up the threads on two of the four main bolts, as well as the threading that the bolts screw into. i don't think they're stripped, they probably just need to be chased (is that what you call it?)...

Hey I was taking my tow hooks off to put on a brush guard and lucky me the head of a bolt snapped off so I went bought an easy out tapped the bolt screwed in the easy out and me and my electric drill arnt strong enough to twist the bolt out. Any suggestions? Also when I get the mounting brackets...