Toyota Nation Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-15 of 15 Results
  1. Tacoma 3rd Generation (2016+)
    I have a 2016 tacoma sr5 2wd and I put a 3 inch leveling block in the front and 2-4” lift KSP upper control arms and my camber is visibly positive and it’s starting to cause uneven tire wear. Any help?
  2. C-HR
    How do you adjust the camber bolt on the rear control arm? Just wanna go a little negative cause my tire is hitting the plastic trim.
  3. Tacoma 1st Generation (1995.5–2004)
    Hey guys I have a 96 regular cab tacoma with the 2.4l that I lowered back in July and I guess I messed with the camber slightly. Its wearing the inside of my front tires pretty good any advice or help is much appreciated... TACOMA ON BABY.
  4. Camry 8th Generation (2018+)
    Hi all, new to the forum browsed for years but I have a 2019 Camry 4cyl and recently did air suspension on it I have adjustable rear control arms but cant seem to find anything for the front. I know camber bolts are an option but I had them and they dont have enough adjustment. Any suggestions ?
  5. Tercel, Paseo, Starlet, and Sera Forum
    Hello everyone, I have an unusual question to ask. I am wondering if it is at all possible to add any sort of negative camber to the rear of a '98 Tercel, and if so, how to do it. I am wanting to do a "stance" look on the car (could very possibly be a dumb idea) and I am not sure how to go about...
  6. Corolla 7th Generation (1993-1997)
    Hey guys, I just put my coilovers on my 94 ae101 today. When I bought the car it came with some pretty conservative 17" wheels on it. i think 17's are too big. I'm looking at some 15x8 wheels with a zero offset right now. I'm just curious to hear and see what some of you guys are running on your...
  7. Corolla 9th Gen/1st Gen Matrix (2003-2008)
    Hello guys, my 07 got some new coilovers on and my rear has no camber at all and is rubbing. The front has around -3 but now i have rear camber shims and 1 inch spacers too. My question is can a shop like NTB or Brakecheck install spacers and shims, because that'll be a bonus for me as i can get...
  8. Tacoma 2nd Generation (2005-2015)
    Hi, Got another question for everyone. Lifted my 2006 Tacoma with a 2" spacer on the front and extra leaf springs in the back. Turns out for some reason it's a bit over 2" at about 2.5" in the front and 3.5" in the back. That's okay by me. However I do notice the camber on the vehicle's front...
  9. Sequoia Forum
    I have a 2010 Sequoia Platinum with just under 25K miles and it wore the rear tires excessively on the inside to the point I need replacements already. So I brought it to my local Toyota dealer for an alignment and naturally it was off. After the alignment, I was looking at the before/after...
  10. Camry & Solara Lounge
    I want to try a DIY string alignment to see if I can get figure this out before I replace my front tires. Plus, I want to replace my front struts before paying for an alignment. As you can see below, I have premature tire wear on the inside shoulder of both front tires. Passenger side is much...
  11. Corolla 9th Gen/1st Gen Matrix (2003-2008)
    So far i found Eibachs Camber Arm Kits, but i'm not sure if they're good for a Corolla S. Any other Camber Arm Kits brands that are good for it?
  12. Camry 7th Generation (2012-2017)
    I will be installing the Eibach Pro Kit on my Camry next week and have heard many people saying that they installed these too. Are these necessary? I didn't have to do this on my Cobalt with sportlines (i know, different car, different springs).
  13. Camry 3rd and 4th Gen '92-'01, Solara '99-'03
    I have a 4cyl 4th gen Camry, I will soon be getting rims and coil-overs. I was wondering on the best and safest way to achieve -5 degree camber. Just looking for basic suggestions and looking to see if anybody else has done it. thanks guys!
  14. Camry 1st and 2nd Gen (1983-86) and (1987-91)
    Aloha everyone, My rear fenders have already been professionally rolled, but my sidewalls are still getting shredded by the fender... I recently purchased camber bolts and tried adjusting for more negative camber so the tires would clear the fender. Problem is, I was only achieving positive...
1-15 of 15 Results
Top