Toyota Nation Forum banner
pulley
1-19 of 23 Results
  1. Camry 1st and 2nd Gen (1983-86) and (1987-91)
    Does anyone know where to find the right pulley for a 1st gen Oil Pump? I ordered a new oil pump and the pulley is wrong. All the ones I see are the wrong tooth pattern, they seem to be for the next gen. This is the only picture I can find for what I need, from a rebuilt long block on ebay Here...
  2. Camry 5th and 6th Gen '02-'11, Solara '04-'08
    Hey all, I have a 2009 Toyota Camry XLE with the V6 (2GR-FE) engine, and recently I've started hearing chirping noises coming from the belt system on the right side of the engine. I can't figure out what it is exactly, but here is a video of the sound I'm talking about: New video by Zareef Huq I...
  3. Camry 7th Generation (2012-2017)
    I've got a 2014 2.5, and I was going to put on a lightweight crank pulley from NST. Only problem is, I cannot find the torque spec for the crank bolt anywhere. If anybody has any clues, please let me know. Thanks
  4. Sequoia Forum
    I have a timing issue on my 2010 Sequoia (Engine 3UR-FE 5.7L) and hope I can get some advice about whether this repair is urgent. The check engine light keeps coming on with code P0014 (camshaft position B timing over advanced). The Toyota dealership service says it “needs cam gear and...
  5. Pre-88 Toyota Pickup/Hilux
    Hi Folks looking for replacement bearings for AC compressor pulley and idler arm pulley. does anyone have brand name and part numbers ? 1986 Toyota 4WD SR5 EFI X-tra Cab Thanks Jim
  6. Camry 3rd and 4th Gen '92-'01, Solara '99-'03
    Doing the timing belt job and decided to change out the oil pump seals as well. The flanged hex nut on the oil pump pulley was totally seized on there (12mm) and so had a difficult time removing it. Definitely more than the 21 ft/lb that the manual calls for. Ended up rounding out and marring...
  7. Tercel, Paseo, Starlet, and Sera Forum
    Starlet 1998 1.3 Hi, so I was having problems with my battery dying and got the multi meter to test the alternator, it was only giving 7 odd volts so was going to return it (still under warranty) when I noticed a nasty very loud noise coming from around the crankshaft. the Inner pulley wheel of...
  8. Corolla 7th Generation (1993-1997)
    I'm trying to figure out what the pulley is called so I can replace it. The car is a 93 Corolla with the 1.6l SOHC engine. I thought it was the harmonic balancer but I think that's the same as the crankshaft pulley. It is the other pulley that accommodates 2 belts. One I believe goes to the...
  9. Corolla 9th Gen/1st Gen Matrix (2003-2008)
    I bought a new pulley for my tensioner, but I guess the bolt holding it in is a torx for 2006 and later. I am curious how people have gotten it out. (and just to verify, I am turning the wrench toward the windshield, am I just stupid and turning the wrong way????? - its so tight that I cant tell)
  10. Avalon 2nd Generation (2000-2004)
    '02 Avalon with 250K miles. This summer I had my mechanic replace all the belts (was 40k overdue). A few days after I got it back there was quite a bit of belt squeak. He took it for a day and adjusted everything. It was fine for 2-3 months. Then every time I started it there was a shrill...
  11. Corolla 8th Generation (1998-2002)
    I'm wondering if there exists a set of lightweight (not underdrive) accessory (not crank) pulleys for the 1ZZ-FE engine. If so, could anyone tell me the brand and/or give me a link?
  12. Camry 3rd and 4th Gen '92-'01, Solara '99-'03
    So, I was replacing my girlfriend's 1996 Camry's front brakes and as I was testing the car out, I heard a wonderful noise coming from the drive belt assembly. I thought it might be a belt problem but after inspection, it appears to be the harmonic balancer wobbling really bad. I looked and it...
  13. Car Parts for Sale
    Seller Name: Chris Location: Charlotte, NC Payment Method: PayPal (no gifts) UR Underdrive Crank Pulley for the 5SFE engine (made for an MR2 but will fit any 5SFE). In good condition. A little dirty on the backside, but nothing that can't be polished out and cleaned up. Used on a Gen 4 Camry...
  14. Corolla 10th Gen/2nd Gen Matrix (2009-2013)
    It's a 2010 Corolla LE with VIN 1nxbu4ee4az26xxxx. It has 69700 miles on it. and I purchased the car used. It makes loud noise from the belt area. Took it to a shop. They replaced the belt, and noise remains. They said alternator causes the noise, and want to replace it.. I am not sure what...
  15. Tercel, Paseo, Starlet, and Sera Forum
    Forgive me if I'm duplicating a thread, I didn't see one in my initial, nowhere near thorough, search. When my Tercel starts up it squeals, then keeps with the high pitched noise when it runs. I'm assuming it's the idler pulley. it's coming from the belt area, and it looks like the belts could...
  16. Car Parts for Sale
    Brand New Unorthodox Racing Ultra S Crankshaft Pulley for a 83-91 Camry 2.0L/ 86-99 Celica 2.0L/2.2L and 96-99 Rav4 2.0L. I think the engine is the 5SFE but I could be wrong. Asking $100+shipping via Paypal. :)
  17. Corolla 10th Gen/2nd Gen Matrix (2009-2013)
    Does anyone know where I can find instructions online to remove the idler pulley? I found a Toyota repair manual but it doesn't say anything about it. I just wanted to prepare instead of going in blind so that I can minimize downtime. TIA
  18. Corolla 6th Generation (1988-1992)
    On my 1991 All-Trac wagon, 4A-FE, I just did my first ever timing belt job, along with replacing the water pump. Here's what I learned. 1. The Toyota Factory Manual is an incredibly valuable resource. If you don't own one, get one. 2. This job was a good excuse to buy more tools without...
  19. Corolla 8th Generation (1998-2002)
    Hello everyone, I am new in this forum and I would like to have your advise on which of these 5 belt tensioners to choose: 1- Duralast - Autozone $123.04 (tax included)...
1-19 of 23 Results
Top