Search Results for ‘torque’

Hey y'all, Would anyone know the torque specs for the 19 Hatch front strut tower bolts? I am installing an aftermarket strut brace and I would like to confirm the ft. Lbs per the service manual. I was recommended 59 ft.-lbs of torque. However I am seeing 37ft.-lbs in numerous places no from...

Looking for Camry 2018 V6 Engine Torque Power Curve for Engineering studies

I just installed my Remark quad exhaust, i was wondering what is the torque specs on the spring bolts, (the two that connects from the catalytic to mid pipe) and the bolts that comes with the remark exhaust. Thank you for whoever answers this.

I'm going to change the coolant and want to make sure all the screws/nuts/bolts involved are tightened to spec. It's my first time doing this kind of DIY and wonder where I can find relevant torque info. Thanks Edit: the engine is 2.2 L 5S-FE I4

I drive a 2019 Toyota Camry SE, and I was wondering what kind of horsepower and torque enhancements are out right now? 203 horsepower and 184 lbs of torque is way too low for my taste. So far I know of the Cat-Back performance exhaust, but that’s about it. I don’t know if any brands of the cold...

I've got a 2014 2.5, and I was going to put on a lightweight crank pulley from NST. Only problem is, I cannot find the torque spec for the crank bolt anywhere. If anybody has any clues, please let me know. Thanks

I did a search but couldn't find the answer. Posting on behalf of a friend: I'm working on a 1999 Toyota Camry XLE 3.0 engine. I'm doing both CV Axles replacement. What is the axle nut torque? 217 ft lbs? Thanks in advance for the help.

Be grateful if anyone with a FSM could give me the torque spec for the nut that holds the wiper arm to the transmission. Just replaced both sides and I think I have it a bit over torqued. Cheers from DE

What up Corolla owners. Ive got a TRD drop-in air filter w/OEM intake setup and a muffler delete on my daily E170. Basically a poor man's attempt at upgrading the airflow. Looking at the INJEN SP CAI and possible Borla axle-back exhaust for slight improvement for torque, HP and fuel economy...

The torque converter is located between the engine and transmission on most vehicles with an automatic transmission. It is responsible for connecting the engine to the transmission. Here's a video on how it works: The torque converter sits in the bell housing in front of the transmission...

Looking to see how many people have had an issue with their torque converter and those who have not. Curious to see how widespread it is or if it was just a handful of vehicles. Just for my own curiosity. No problems yet at 36k miles.

Hello TN, I will be replacing brake pads and rotors on my 2012 Camry LE very soon. Does anyone know what the factory service manual torque specs are for caliper bolts and caliper bracket bolts? Could I get the banjo bolts torque spec to for future use? I see a lot of "should be the same as"...

6th/7th-Gen Dyno Results Thread I think it may be a good idea to compile a list of dyno result charts so that we can get an idea of whp from our cars and understand how they respond to mods. V-6: BlackCamSe (CAI, Borla exhaust, resonator delete): 230hp, 233 ft-lbs, Mustang Dyno (see thread)...

I have a coolant sensor (SENSOR, WATER TEMPER 89422-20010) that is leaking (oddly at the body / connector interface, not at the threads). I think I can get a socket on it (deep, thin wall: another new purchase yay). But does anyone know the proper torque for this sensor (it's on the top of the...

Hi All, My toyota camry 1994 v6(1MZ-FE) showing its SES light(engine light) on, From little searching on google I found, 1994 camry v6 first implemented obd II. I found the OBD II connector behind the coin box. I want to connect Torque( Android App: Link ) to car OBD system using ELM 327. Any...

I saw this Torque app on the Google Marketplace (for Android Phones/Tablets) and watched a few videos on it, it seemed pretty cool. I got a OBDLink MX OBDII Bluetooth adapter (has a very fast poll rate), and bought the app, and a plugin for it. I couldn't be happier! So far at least... It kind...

I have a 1992 Camry LE, 5SFE engine, automatic transmission. I have replaced the dogbone mount once before, and it fit right in with no problems. Yesterday, I noticed the rear mount and dogbone mount were both bad, so I replaced them. After putting in the rear mount (which required a pry bar...

Anyone know the lug nut torque setting for the '98 Avalon? I have the aluminum or aluminum/magnesium wheels and was wondering if it makes a difference in the setting if you have those versus a steel wheel with a cover or another wheel? Any other insight or words of advice would be much...