Can somebody show me diagram how to take off the front bumper?
1 - 19 of 19 Posts
i too would like to know how to take my front end off. front quarter panels, pumpers, headlights. Any one know? BTW it an 05 Camry.
check the stickies for the general camry discussion, the repair manuals are posted there. for a general how-to though, here you go:
*i advise you to lift the front end up before starting... it makes accessing things much easier.
1. remove all bolts holding the splashguards to the bumper (all the bottom bolts). and yes, remove the one that looks like its just holding the wheel well splashguard and the engine splashguard together. should be 9 bolts i believe, i'm not sure.
2. either remove the wheel well splashguard or remove enough bolts and clips so that you can access the bolt holding the top edge of the bumper to the fender. the wheel well splashguard is clipped to the bumper, do not forget to remove the clip and pull the splashguard out of the bumper clip "lock". do both sides, obviously.
3. remove the top bolts and clips located at the top of the bumper, under the grill location.
4. pull out the bumper at both fenders, don't be afraid to pull hard to release the clips. you should now be able to remove the front bumper.
*i advise you to lift the front end up before starting... it makes accessing things much easier.
1. remove all bolts holding the splashguards to the bumper (all the bottom bolts). and yes, remove the one that looks like its just holding the wheel well splashguard and the engine splashguard together. should be 9 bolts i believe, i'm not sure.
2. either remove the wheel well splashguard or remove enough bolts and clips so that you can access the bolt holding the top edge of the bumper to the fender. the wheel well splashguard is clipped to the bumper, do not forget to remove the clip and pull the splashguard out of the bumper clip "lock". do both sides, obviously.
3. remove the top bolts and clips located at the top of the bumper, under the grill location.
4. pull out the bumper at both fenders, don't be afraid to pull hard to release the clips. you should now be able to remove the front bumper.
as for the headlights, they are held in by two bolts and two clips. remove the two bolts, then pull up on the headlight to disengage the bottom clip. then pull out on the headlight to disengange the "pin" clip on the back of the headlight. you might have to pull pretty hard to get it off... be wary of sharp edges!
can you send us the link to a repair manual? so i can see diagrams on exactly what I'm doing. And BTW, I'm not trying to be a thread stealer Lol
maybe it wouldn't be so ridiculous if u would just post up a link so i don't have to keep make people say its ridiculous.njerald said:
This weeks ridiculous post
The Toyota Technical Information System link is
http://www.techinfo.toyota.com/
Its $10 for 24 hours of browsing and saving the pdf files you want.
The Toyota Technical Information System link is
http://www.techinfo.toyota.com/
Its $10 for 24 hours of browsing and saving the pdf files you want.
http://oregonstate.edu/~tongt/camry/07/index.html
found it. fairly easy, i did brake some tabs though so becareful.
found it. fairly easy, i did brake some tabs though so becareful.
Great find...djpeetur said:
Hope Oregon State got permission from Toyota to publish copyright material..
This is exactly what you have to pay $10 a day for access to the TIS database.
Thanks for the clarification..njerald said:
This forum rocks with great info and knowledgeable owners.:clap:
Have had my XLE for a week know and getting to appreciate some of the features more and more.
By the way in your sig you state you have "emblem changes" what did you do(other than the Lexus logo on the front)?? Remove/Add??
Joined
·
1,085 Posts
^ What kind of wrench would I need to remove the bolts? Will adjustable work? If socket, how many mm? TIA.
Joined
·
1,085 Posts
^ Also, where can I find a 10mm socket wrench? I just need one, not a whole set. I couldn't find any at Pepboys =[. Would Home Depot be selling one?
Joined
·
325 Posts
Starting with the hood open, take out that 10mm hex black screw in the middle. Then take a philips #2 tip and take out the two rubber bump stops for the hood (one toward the driver and one toward the passenger side). Then... along the same area you'll notice a bunch of plastic pushin round tabs all along that area. You ONLY need to take out 1 near each of the headlight. And it would be the Second To Last on each side. So not the one that's right next to the headlight, but the second one away from the headlight.
That basically completes the top.
Under the bumper on the permeter will be a bunch of grayish 10mm socket hex screws so remove those. Then when you get to either end, there will be a BLACK 10mm socket hex screw. Only take one out from each end, the one on the edge of the bumper, you don't need to remove the other 2 next to them.
Then in your wheel well, in front of each tire you'll noticed a plastic tab. Take a flat screw driver and turn it 1/4 turn. Then pull it out, like all the way out. You can't leave part of it in there, you have to pull it out, either take a plyer or something.
One last 10mm hex gray screw is behind that wheel well flap. You can take a screw driver and push the black flap away where the bumper meets the fender. You'll see that 10mm gray hex screw. Just remove it with a socket or a philips screw driver.
also if you have the air dams infront of your front wheel, you also have to remove 2 screws, there to get the bumper off
Pull on each side of the bumper. Pull it forward and at the same time lift the bumper up so the top of the bumper (where it meets the hood) can come off the rails.
And that's it. When I first took it off, i had the car on a lift so I took all the black plastic panels underneith the car off too hehe which wasn't needed. But when you put it back together, you have to make sure part of those black panels slide into the bumper and some of it doesn't. The ones where you took those gray 10mm hex screws are the ones that has to be on the outside or below the bumper, not into it.
That basically completes the top.
Under the bumper on the permeter will be a bunch of grayish 10mm socket hex screws so remove those. Then when you get to either end, there will be a BLACK 10mm socket hex screw. Only take one out from each end, the one on the edge of the bumper, you don't need to remove the other 2 next to them.
Then in your wheel well, in front of each tire you'll noticed a plastic tab. Take a flat screw driver and turn it 1/4 turn. Then pull it out, like all the way out. You can't leave part of it in there, you have to pull it out, either take a plyer or something.
One last 10mm hex gray screw is behind that wheel well flap. You can take a screw driver and push the black flap away where the bumper meets the fender. You'll see that 10mm gray hex screw. Just remove it with a socket or a philips screw driver.
also if you have the air dams infront of your front wheel, you also have to remove 2 screws, there to get the bumper off
Pull on each side of the bumper. Pull it forward and at the same time lift the bumper up so the top of the bumper (where it meets the hood) can come off the rails.
And that's it. When I first took it off, i had the car on a lift so I took all the black plastic panels underneith the car off too hehe which wasn't needed. But when you put it back together, you have to make sure part of those black panels slide into the bumper and some of it doesn't. The ones where you took those gray 10mm hex screws are the ones that has to be on the outside or below the bumper, not into it.
1 - 19 of 19 Posts
Join the discussion
